Product Catalogue2 sections · 4 product types

Lifting & Pulling

The tools for moving heavy parts a short distance with control: raising a machine or vehicle, lifting a load to working height, and drawing a bearing, gear or pulley off a shaft without damaging either. Small category, high stakes. Most of these jobs go wrong through under-rating rather than through wear.

Lifting & Pulling supplied by Balaji Enterprises, Indore

Jacks & Lifting

Jacks & Lifting: table lifter

Hydraulic bottle jacks and trolley jacks in a range of tonnages, and table lifters that raise a load to bench height for assembly or mould handling. Choose a jack by capacity, minimum height (it has to fit under the load) and lift range. A bottle jack is compact and strong; a trolley jack rolls into position and lifts faster. A jack is for lifting only. Support the load on stands before anyone works under it.

Jacks & Lifting we supply

  • Hydraulic Bottle Jack
  • Table Lifter

Pullers

Pullers: bearing puller

Two-jaw and three-jaw gear pullers, and bearing pullers and separators that get behind a bearing seated tight against a shoulder. Size a puller by reach (how far the jaws extend along the shaft) and spread (the widest diameter they open to), not by tonnage alone. Three jaws grip more evenly and are less likely to slip off.

Pullers we supply

  • Bearing Puller
  • Gear Puller

Brands we supply for jacks and pullers

Lifting and pulling tools must be rated honestly. We supply lines whose capacity markings we trust.

Authorised distributor
StanleyBottle and trolley jacks, table lifters, and bearing and gear pullers.
De NeersBearing pullers and hydraulic jacks, with deep coverage on puller span for mill and press drives.
GrozBearing pullers and hydraulic jacks for workshops.
TapariaBearing pullers and hydraulic jacks.

Industries that buy jacks and pullers from us

Buying jacks and pullers: what to get right

What to specify

  • Capacity with margin

    Rate the jack or puller above the heaviest load or tightest fit you expect.

  • Jack heights

    Minimum height to get under the load, and the lift it gives.

  • Puller reach and spread

    Measure the distance from shaft end to the back of the part, and the part's outside diameter.

Common mistakes

  • Working under a jacked load

    Hydraulic jacks can creep or fail. Always use stands.

  • Too small a puller

    Forcing an under-sized puller bends the jaws or the centre screw, and it usually slips at the worst moment.

  • Pulling on the outer race

    Pulling a bearing by the wrong race damages it. Use a separator behind the inner race where you can.

Quality tiers

  • Industrial

    Higher-tonnage jacks and heavy pullers for plants and mills.

  • Workshop

    General-purpose jacks and pullers for maintenance bays and vehicle work.

Why buy jacks and pullers from Balaji Enterprises

Tell us the load, the clearance or the bearing dimensions and we will size the jack or puller for you, rather than leaving you to guess from a tonnage figure. We have supplied plant maintenance teams around Indore from Siyaganj since 1996.

Lifting & Pulling: questions buyers ask

What capacity jack do we need?

Take the weight on the lifting point (often half or a quarter of the total, depending on where you lift) and add a safety margin. Then check the jack's minimum height fits under it.

Two-jaw or three-jaw puller?

Three-jaw for round parts. It grips evenly and slips less. Two-jaw where access is tight or the part has only two pulling points.

How do I size a bearing puller?

Measure the bearing's outside diameter (for spread) and how far the jaws must reach behind it along the shaft (for reach). Send us both.

Can a table lifter be used for mould changes?

For moulds and parts within its rated load, yes. It raises the load to working height and moves it on castors. Check the platform size against the mould.

Fitting out a plant, a site or a crew?

Request a quote for jacks and pullers

Send the load, the clearance or the bearing dimensions, and we will size and quote the right tool.

Balaji Enterprises30 years in industrial tools & MRO · Indore, MP